Your AC is running but the room is not getting cold? The most common reason is low refrigerant gas. But before we refill anything, we make sure the gas will actually stay — because adding gas without checking for leaks is just wasting your money.

How We Do It — Step by Step

Most technicians just refill the gas and leave. We do it differently.

✅ Step 1 — Full AC Inspection

Before touching the gas, we inspect your entire AC — indoor unit, outdoor unit, pipes and joints.

✅ Step 2 — Leak Test with Soap Foam

We apply soap foam on every pipe joint and connection point. If there is a leak, bubbles will appear — we find it and fix it first. No leak test, no gas refill — that's our rule.

✅ Step 3 — Pressure Check

We use a pressure gauge to check the current gas level and confirm how much needs to be refilled.

✅ Step 4 — Gas Refill

We refill with the correct gas type — R22, R32 or R410A — based on your AC model. The right gas in the right amount makes all the difference.

✅ Step 5 — Final Performance Check

After refilling, we run your AC and check the cooling performance — so we leave only when everything is working perfectly.

Why choose our AC Gas Refil service in Mirpur,Dhaka

Mirpur's voltage fluctuation environment creates a specific gas leak mechanism that our technicians understand and address during every gas refill service here. Repeated voltage surges cause the AC compressor to cycle irregularly — creating pressure fluctuations within the refrigerant circuit that stress flare connections and valve seats over time. A connection that holds perfectly under normal operating pressure can develop micro-leaks when subjected to repeated pressure spikes from voltage instability. This is why Mirpur ACs often require gas attention sooner than ACs in areas with stable power. Our Mirpur workshop near Section 10, operating in partnership with Al-Amin Refrigeration's gas supply point in Mirpur, maintains consistent availability of R22, R32 and R410A for the wide variety of AC models installed across Mirpur's diverse residential stock. For every Mirpur gas refill call, our technician performs the leak test with specific attention to compressor output connections where voltage-related stress most commonly manifests.

Our Other Services

◉ AC Basic Wash ◉ AC Foam Wash ◉ AC Jet Wash

◉ AC Master Servicing ◉ AC Installation

◉ AC Uninstall & Re-install ◉ AC Leak Repair

Pricing

Gas Type	1 Ton	1.5 Ton	2 Ton
R22	Starting from৳3,000	Starting from৳3,500	Starting from৳4,000
R32	Starting from৳2,500	Starting from৳3,000	Starting from৳3,500
R410	Starting from৳2,500	Starting from৳3,000	Starting from৳3,500
R407	Starting from৳2,500	Starting from৳3,000	Starting from৳3,500

⚠️ If hanging or scaffolding is required, additional charge applies. Final price confirmed by technician on-site.

▪️ How do I know if my AC needs gas refill?

If your AC runs but doesn't cool properly, takes too long to cool, or the outdoor unit runs non-stop — these are signs of low gas.

▪️ Why do you check for leaks before refilling?

If there is a leak and we just add gas, it will escape again within days or weeks. We fix the leak first so your gas lasts long — saving you money in the long run.

▪️ How long does gas stay after refilling?

If there is no leak, gas can last 2 to 5 years depending on usage and AC condition.

▪️ What gas type does my AC use?

It depends on your AC model. Our technician will check and use the correct type — R22 for older models, R32 or R410A for newer ones.

▪️ Is there a guarantee after gas refill?

Yes. 10-day guarantee. If gas drops again within 10 days due to a leak we missed, we come back and fix it for free.

Q: My Mirpur AC keeps needing gas refill every few months — why?

A: Repeated short-interval gas loss in Mirpur almost always indicates a leak that previous technicians did not find or properly repair. Our mandatory leak test using soap foam on every circuit joint identifies these leaks before we add any gas. We repair the leak first — even if it takes additional time — because refilling without repairing is money wasted.

Q: Does Mirpur's voltage problem damage the AC refrigerant circuit?

A: Voltage fluctuation stresses compressor components and can gradually weaken flare connections through repeated pressure variation. We check specifically for voltage-related connection stress during our Mirpur leak tests and recommend voltage stabilizer installation alongside gas service where this pattern is identified.

Q: Which areas of Mirpur does your workshop near Section 10 serve?

A: Our Mirpur workshop serves all of Mirpur sections 1 through 14, Pallabi, Kalshi, Piroerbag and Mirpur DOHS. Gas is available same-day for all these areas from our Section 10 supply point.

Tap the call button on top of the page

Go to Contact page, select your service, enter your name, phone number and address — done!

📞 Call: 01736092803

💬 WhatsApp: 01736092803

Gas refill service active across all Mirpur sections 1 through 14, Pallabi, Kalshi, Piroerbag and Mirpur DOHS. Refrigerant supply supported by Al-Amin Refrigeration's Mirpur gas supply point. Voltage-related connection stress assessment included in all Mirpur leak tests. Same-day service available throughout Mirpur.